-
SKUOX01F10-E48Y-GD
OX01F10-E48Y-LD
OX01F10-E48Y-OD -
Packagea-CSP™
a-CSP™
a-CSP™
SoC Offers Rear and Surround View Cameras Industry's Best Low-Light Performance, Lowest Power and Smallest Size
OMNIVISION’s OX01F10 is a 1.3MP SoC, providing automotive designers with the industry’s best imaging performance across a wide range of challenging lighting conditions, along with the most compact form factor and lowest power consumption. In a single, 1/3.55″ optical format package, the OX01F10 integrates a 3.0 µm image sensor and an advanced image signal processor (ISP) with OMNIVISION’s PureCel®Plus‑S technology for low noise, solving the automotive rear view camera (RVC) and surround view system (SVS) challenges of achieving a small form factor with excellent low-light performance, ultra-low power and reduced cost while improving reliability by using only one printed circuit board (PCB).
This SoC employs dual conversion gain (DCG™) technology to achieve high dynamic range with only two captures, as opposed to three required by the competition, which minimizes motion artifacts while reducing power consumption and boosting low-light performance.
The OX01F10 power consumption is 30% lower than competitors and significantly reduces the temperature. It does not require a metal heat sink, allowing for the use of plastic camera module bodies to reduce costs. With its compact package size, it also enables smaller cameras that can fit in much tighter spaces. In addition, by integrating both the image sensor and ISP into a single chip, designers can save on both cost and space by eliminating the second PCB in typical two-chip implementations.
This SoC provides 1.3MP resolution and a 1340 x 1020 array size at 30 fps, offering ample resolution for calibration. It also enables output flexibility with both 2‑lane MIPI and 10‑bit DVP interfaces, and is AEC‑Q100 Grade 2 certified.
Support for image size:
– 1340 x 1020 and any cropped size
High dynamic range
High sensitivity
Dual conversion gain
ASIL-B safety feature
Image sensor process functions:
– AEC/AGC/AWB
– Lens correction
– Defective pixel correction
– HDR combination
– Tone mapping
– Automatic black level correction
Supported output formats:
– YUV
– RGB888
– BT656
– RAW
SPI master for loading settings
50/60 Hz flicker cancellation
SCCB for register programming
Programmable GPIOs
High speed serial data transfer with MIPI CSI-2 or DVP
External frame synchronization capability
Embedded temperature sensor
One-time programmable (OTP) memory
-
SpecOX01F10
-
Analog / DigitalDigital
-
Category1MP and Below
-
CFA (Chroma)Color
-
Frame RateFull @ 30 fps
-
Image Area4080 x 3108 µm
-
InterfaceMIPI
-
Optical Format1/3.55" for 1340 x 1020 image size
-
Output Format3-exposure HDR, Dual exposure HDR (long and short), Linear output
-
Packagea‑CSP™
-
Pixel Size3.0 µm
-
Power RequirementActive: 270 mW/260 mW (streaming 1280 x 720 @ 30 fps YUV DVP/MIPI typical), Active: 315 mW/300 mW (streaming 1280 x 960 @ 30 fps YUV DVP/MIPI typical), Active: 335 mW/315 mW (streaming 1340 x 1020 @ 30 fps YUV DVP/MIPI typical)
-
Resolution1.3MP
-
Shutter TypeRolling Shutter
-
TechnologyHDR, PureCel®Plus‑S
-
Use CaseViewing Applications - E-mirrors, Viewing Applications - Rear View Camera, Viewing Applications - Surround View Camera